No products in the cart.
RCD PERFORMANCE RESOURCES
Forms
WARRANTY CLAIM FORM CPX MANUAL INJECTOR TEST FORM DEALERS APPReference Guides
6.0L POWER STROKE REFERENCE GUIDE 6.4L POWER STROKE REFERENCE GUIDE 6.7L POWER STROKE REFERENCE GUIDE 2011-2019 6.7L POWER STROKE REFERENCE GUIDE 2020+6.0L Torque Specs
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| Air inlet duct clamp | 5 | — | 44 |
| Turbocharger exhaust adapter V-clamp | 12 | 9 | — |
| Exhaust tube to exhaust manifold flange bolts (left side) ᵃ | 27 | 20 | — |
| Exhaust tube to exhaust manifold flange bolts (right side) ᵃ | 27 | 20 | — |
| Turbocharger flange to exhaust/EGR tube bolts (right side) ᵃ | 27 | 20 | — |
| Turbocharger mounting bolts | 38 | 28 | — |
| Turbocharger pedestal bolts | 31 | 23 | — |
| Turbocharger oil supply tube bolts | 24 | 18 | — |
| Exhaust manifold flange bolts ᵃ | 38 | 28 | — |
| Intake manifold flange bolts | 11 | 8 | — |
| Intake manifold heat shield | 11 | 8 | — |
| EGR valve mounting bolts | 13 | 10 | — |
| EGR clamp, V-band | 6 | — | 53 |
| EGR cooler bolts (M8 x 16) | 31 | 23 | — |
| EGR cooler stud bolts (M6 X 55 X 20) | 13 | 10 | — |
| Crankcase breather nuts | 7 | — | 62 |
| Fuel injector hold-down bolt | 33 | 24 | — |
| Rocker arm fulcrum plate | 31 | 23 | — |
| Glow plugs | 19 | 14 | — |
| ICP sensor | 12 | 9 | — |
| High pressure tube (case to head) | 45 | 33 | — |
| Oil rail check valve | 34 | 25 | — |
| Oil rail vent plugs | 11 | 8 | — |
| Oil rail | 96 | — | — |
| Valve cover bolts and studs | 8 | — | 71 |
| Oil drain pan plug | 44 | 32 | — |
| Front cover module bolts | 24 | 18 | — |
| Thermostat housing retaining bolts | 23 | 17 | — |
| Coolant pump mounting bolts | 23 | 17 | — |
| Oil pump housing retaining bolts | 8 | — | 71 |
| Lower crankcase outer bolts (M8 x 30) | 24 | 18 | — |
| Oil pickup tube flange bolts | 13 | 10 | — |
| Piston cooling jet mounting bolt ᶜ | 13 | 10 | — |
| Cam follower mounting bolt | 13 | 10 | — |
| Camshaft thrust plate mounting bolts | 31 | 23 | — |
| Coolant heater | 41 | 30 | — |
| Oil cooler mounting bolts (6mm) | 10 | — | 89 |
| Oil cooler mounting bolts (8mm) | 22 | 16 | — |
| Oil cooler-to-oil cooler cover bolts | 22 | 16 | — |
| Oil cooler-to-oil cooler cover nuts | 22 | 16 | — |
| EGR cooler coolant supply port cover (M6) | 10 | — | 89 |
| Oil filter housing bolts (torx) | 15 | 11 | — |
| Oil filter return tube bolt, new base | 5 | — | 44 |
| Oil filter return tube bolt, reinstallation | 3 | — | 27 |
| Crankshaft position (CKP) sensor | 11 | 8 | — |
| Camshaft position (CMP) sensor | 11 | 8 | — |
| Injection control pressure (ICP) sensor | 12 | 9 | — |
| Injection pressure regulator (IPR) valve | 50 | 37 | — |
| Manifold air temperature (MAT) sensor | 17 | 13 | — |
| Exhaust back pressure tube assembly | 30 | 22 | — |
| Exhaust back pressure (EBP) sensor | 12 | 9 | — |
| Exhaust back pressure (EBP) sensor bracket | 12 | 9 | — |
| Lower oil pan bolt | 13 | 10 | — |
| Upper oil pan bolts (M6) | 13 | 10 | — |
| Engine coolant temperature (ECT) sensor | 12 | 9 | — |
| Glow plug | 19 | 14 | — |
| Glow plug relay | 11 | 8 | — |
| High pressure oil pump cover bolts | 11 | 8 | — |
| High pressure oil pump mounting bolts | 24 | 18 | — |
| High pressure oil pump discharge tube mounting bolts (top of pipe) | 8 | — | 71 |
| Rear heat shield (M6 x 1.0 x 1.2) | 11 | 8 | — |
| Rear heat shield (M10 x 1.5 x 16) | 49 | 36 | — |
| Banjo bolt with copper sealing washers | 38 | 28 | — |
| Banjo bolt with Viton® sealing washers | 25 | 18 | — |
| Fuel filter plug assembly (back of head) | 27 | 20 | — |
| Flywheel/flexplate mounting bolts | 94 | 69 | — |
| Fuel supply and return tubes at filter | 43 | 32 | — |
| Right and left head supply tubes at filter | 26 | 19 | — |
| Front lifting eye (M10 x 30) | 41 | 30 | — |
| Rear lifting eye (M10 x 35) | 41 | 30 | — |
| Automatic transmission tube nut | 8 | — | 71 |
| Engine ground strap bolt | 10 | — | 89 |
| Starter positive cable nut | 12 | 9 | — |
| Starter control wire nut | 6 | — | 53 |
| Torque converter nut | 35 | 26 | — |
| Motor mount nuts | 112 | 83 | — |
| Turbo down pipe bolts | 40 | 30 | — |
| Transmission-to-engine bolts | 47 | 35 | — |
| Transmission tubes mounting bracket bolts | 10 | — | 89 |
| Upper oil pan bolts (M8) | 31 | 23 | — |
| Transmission cooler bolts | 8 | — | 71 |
| Power steering cooler bolts | 11 | 8 | — |
| Battery crossover cable nut | 12 | 9 | — |
| Power steering pump bolt | 25 | 18 | — |
| Battery ground cable-to-engine block bolts | 47 | 35 | — |
| Air conditioning compressor bolts | 25 | 18 | — |
| A/C manifold bolt | 21 | 15 | — |
| Coolant pump mounting bolt | 23 | 17 | — |
| Coolant pump pulley bolts | 31 | 23 | — |
| Cooling fan stator bolts | 40 | 30 | — |
| Fan clutch hub-to-coolant pump | 133 | 98 | — |
| Belt idler pulley bolts | 47 | 35 | — |
| Belt tensioner bolts | 25 | 18 | — |
| Crankshaft pulley bolts (dual alternators) | 47 | 35 | — |
| Alternator mounting bracket bolts (dual alternators) | 47 | 35 | — |
| Starter mounting bolts | 25 | 18 | — |
| Solenoid wire nut | 6 | — | 53 |
| Battery cable nut | 12 | 9 | — |
| Injector | 26 | — | — |
| Rod bearing bolts | — | 33 then 50 | — |
| Main bearing bolts | — | 90 then 120 then 170 | — |
| Vibration damper | — | 50 | — |
| Rear engine cover | — | 18 | — |
| Flywheel/flexplate | — | 44 then 69 | — |
ᵃ Apply High Temperature Nickel Anti-Seize Lubricant (XL-2) to the threads prior to assembly.
ᵇ Refer to the procedure in this section.
ᶜ Apply Threadlock 262 to bolt threads prior to assembly.